Atmos Aegis V2 Manual: Complete Setup, Temperature Guide & Troubleshooting

Overview

The Atmos Aegis V2 is a premium dry herb vaporizer featuring an OLED display, precise temperature control from 320°F to 430°F, convection heating, and a unique silicone filtration system. This manual covers everything you need to know for setup, optimal use, and maintenance.

What's in the Box

• Atmos Aegis V2 vaporizer (1650mAh battery)
• Mouthpiece with silicone filter
• Packing tool
• Cleaning brush
• Cleaning swabs
• Micro-USB charging cable
• User manual

Note: Dry herb is sold separately.

Device Overview

Components

• Body: Anodized aluminum housing with internal battery
• OLED Display: Shows temperature, battery level, and status
• Mouthpiece: Removable top with silicone filter
• Ceramic Chamber: Convection heating chamber
• Control Buttons: Power, temperature up (+), temperature down (-)
• Micro-USB Port: For charging

Button Functions

Action	Function
5 clicks power button	Power on/off
Single click +	Increase temperature
Single click -	Decrease temperature
Hold + or -	Rapid temperature adjustment
Hold power	Heat and vaporize

OLED Display Information

The display shows:

• Current temperature (large numbers)
• Target temperature (when heating)
• Battery level indicator
• Heating status icon

Getting Started

Initial Charge

Before first use, fully charge your Aegis V2:

1. Connect the Micro-USB cable to the device
2. Connect to a USB power source (5V/1A recommended)
3. Allow 2-3 hours for full charge
4. OLED will show battery full when complete

Note: The device cannot be used while charging.

First-Time Setup

1. Power on with 5 rapid clicks
2. The OLED display will activate
3. Default temperature is typically 380°F
4. Adjust to your preferred starting point
5. Run one empty heating cycle to burn off manufacturing residue

Loading the Chamber

Preparing Your Herb

1. Use quality, properly dried herb
2. Grind to medium-fine consistency
3. Remove stems and seeds
4. Avoid powder-fine grinds that can clog the screen

Loading Steps

1. Ensure device is powered off
2. Unscrew the mouthpiece counterclockwise
3. Locate the ceramic chamber inside
4. Use the packing tool to load ground herb
5. Fill the chamber—don't overpack
6. Leave some space for airflow
7. Replace and secure the mouthpiece

Optimal Packing

• Too loose: Inconsistent vaporization
• Too tight: Restricted airflow, poor vapor
• Ideal: Firm but not compressed, herb moves slightly when shaken

Temperature Guide

The Aegis V2 offers precise temperature control. Here's how to optimize your sessions:

Low Temperatures (320°F - 350°F)

• Light, flavorful vapor
• Emphasis on terpene taste
• Minimal visible output
• Best for: Flavor enthusiasts, new users, microdosing

Medium Temperatures (350°F - 380°F)

• Balanced flavor and vapor production
• Good extraction efficiency
• Visible but not dense clouds
• Best for: Daily sessions, most users' sweet spot

Medium-High Temperatures (380°F - 410°F)

• Fuller extraction
• Denser vapor production
• Some flavor reduction
• Best for: Experienced users, efficiency focus

High Temperatures (410°F - 430°F)

• Maximum extraction
• Very dense, visible vapor
• Significant flavor loss
• Best for: Final extraction of spent herb, cloud chasers

Temperature Tips

• Start low (350°F) and increase gradually
• Higher temps drain battery faster
• Let the device reach target before drawing
• Step up temperature throughout a session for full extraction

Using Your Aegis V2

Powering On

1. Click the power button 5 times rapidly within 2 seconds
2. OLED display will illuminate
3. Device enters standby mode

Setting Temperature

1. Press + to increase temperature
2. Press - to decrease temperature
3. Hold buttons for faster adjustment
4. Temperature adjusts in 1° increments

Taking a Draw

1. Set your desired temperature
2. Hold the power button to begin heating
3. Watch the OLED—current temp will rise toward target
4. When target is reached, begin drawing slowly
5. Continue holding the button while inhaling
6. Release when finished, exhale

Drawing Technique

For optimal vapor with convection heating:

• Draw slowly: Maintains heat in the chamber
• Draw steadily: Even airflow improves extraction
• Pause between draws: Allows reheat
• Don't rush: Convection works best with patience

Auto Shutoff

The Aegis V2 includes safety auto shutoff:

• Engages after 5 minutes of inactivity
• Prevents overheating and battery drain
• Restart by clicking 5 times to power on

Silicone Filter System

How It Works

The silicone filter sits in the mouthpiece pathway:

1. Vapor exits the chamber
2. Passes through the silicone filter
3. Heat is absorbed by the silicone
4. Cooler vapor reaches your mouth

Benefits

• Smoother, less harsh hits
• Reduced throat irritation
• Cooler vapor temperature
• Additional filtration

Maintenance

• Remove and clean weekly
• Check for tears or damage
• Replace if worn (contact Atmos for parts)

Battery Information

Specifications

• Capacity: 1650mAh
• Sessions per charge: 8-12 (varies by temperature)
• Charging: Micro-USB
• Charge time: 2-3 hours
• Passthrough: Not supported

Battery Care

• Avoid complete depletion before charging
• Don't leave on charger indefinitely after full
• Store with 40-60% charge for extended storage
• Avoid extreme temperatures while charging

Maximizing Battery Life

• Use lower temperatures when possible
• Shorter sessions conserve power
• Turn off between uses
• Keep contacts clean

Cleaning and Maintenance

After Each Session

1. Empty chamber while still warm
2. Use brush to remove loose debris
3. Tap device gently to dislodge particles
4. Wipe mouthpiece if needed

Weekly Cleaning

1. Remove mouthpiece
2. Remove silicone filter
3. Brush chamber thoroughly
4. Clean screen with dry cotton swab
5. Clean silicone filter (see below)
6. Wipe exterior with dry cloth

Cleaning the Silicone Filter

1. Remove from mouthpiece assembly
2. Soak in warm water with mild soap, or
3. Soak in isopropyl alcohol (90%+) for 15 minutes
4. Rinse thoroughly with warm water
5. Dry completely before reinstalling

Deep Cleaning (Monthly)

1. Disassemble mouthpiece completely
2. Soak all removable parts in isopropyl alcohol
3. Use cotton swabs with alcohol on chamber (device off and cool)
4. Clean airpath with pipe cleaners
5. Rinse removable parts with warm water
6. Dry all parts completely before assembly

What Not to Do

• Never submerge the battery/body in liquid
• Don't use water inside the chamber
• Avoid abrasive cleaning tools
• Never clean while device is hot or on

Storage

Short-Term Storage

• Power off with 5 clicks
• Empty the chamber
• Store upright in a cool, dry place
• Keep display protected

Long-Term Storage

• Clean thoroughly before storing
• Charge battery to 50%
• Store in original box if available
• Check and recharge every 2-3 months

Troubleshooting

Device Won't Power On

1. Charge for at least 30 minutes
2. Click exactly 5 times within 2 seconds
3. Check Micro-USB port for debris
4. Try a different charging cable/source

OLED Display Issues

Blank display:

• Ensure device is charged
• Try a full charge cycle
• Check if device powers on (button click feedback)

Flickering:

• Avoid extreme temperatures
• May indicate loose connection
• Contact support if persistent

No Vapor Production

1. Verify herb is loaded
2. Confirm device shows heating
3. Wait for target temperature
4. Increase temperature if needed
5. Check that herb is fresh and ground
6. Ensure chamber isn't overpacked

Weak or Poor Vapor

1. Increase temperature setting
2. Grind herb more finely
3. Adjust packing density
4. Clean the chamber and airpath
5. Check silicone filter isn't clogged
6. Use fresher herb

Harsh or Burnt Taste

1. Lower temperature
2. Clean thoroughly
3. Replace with fresh herb
4. Pack more loosely
5. Check silicone filter is installed correctly

Temperature Not Reaching Target

1. Ensure battery is adequately charged
2. Clean chamber for good heat transfer
3. Don't overpack the chamber
4. Allow adequate heat-up time

Device Overheating

1. Stop use immediately
2. Power off and let cool completely
3. Check silicone filter is installed
4. Reduce session frequency/length
5. Contact support if overheating continues

Specifications

Specification	Value
Battery Capacity	1650mAh
Heating Method	Convection
Temperature Range	320°F - 430°F (160°C - 221°C)
Display	OLED
Temperature Increments	1°
Chamber Material	Ceramic
Body Material	Anodized aluminum
Filtration	Silicone filter system
Charging	Micro-USB
Charge Time	2-3 hours
Sessions Per Charge	8-12 (approx.)
Auto Shutoff	5 minutes
Passthrough Charging	No
Warranty	1-year limited

Safety Information

General Safety

• Adult use only (21+)
• Keep away from children and pets
• Use only with dry herb material
• Do not use damaged devices

Electrical Safety

• Use appropriate USB power sources (5V/1A)
• Do not charge with high-powered adapters
• Avoid charging unattended for extended periods
• Keep away from water and moisture

Usage Safety

• Allow cooling between extended sessions
• Do not touch the chamber when hot
• Stop use if device becomes excessively hot
• Use on stable, heat-resistant surfaces

Storage Safety

• Store away from heat sources
• Keep away from moisture
• Do not store with loaded chamber
• Remove from direct sunlight

Warranty Information

The Atmos Aegis V2 includes a 1-year limited warranty:

• Register at atmosrx.com
• Keep purchase receipt
• Covers manufacturing defects
• Does not cover user damage or consumables (filters, mouthpiece)

Related: Atmos Aegis V2 Review | Atmos Jump Manual | What Happened to Atmos Vapes?