Pulsar SYNDR Dry Herb Vaporizer Manual: Setup, Usage & Troubleshooting: Complete Setup & Usage Guide

Overview

The Pulsar SYNDR is a compact dry herb vaporizer featuring conduction heating, four temperature settings, and USB-C charging. Standing 4.25 inches tall, this pocket-friendly device offers single-button operation with haptic feedback for intuitive use.

This manual covers complete setup, operation, maintenance, and troubleshooting for your Pulsar SYNDR to ensure optimal performance and longevity.

What's in the Box

• Pulsar SYNDR Dry Herb Vaporizer
• USB Type-C Charging Cable
• Cleaning Brush
• Stainless Steel Chamber Screens (2)
• Cleaning Swabs (5)
• User Manual

Note: Contents may vary slightly by retailer or special edition.

Getting Started

Initial Charge

Before first use, fully charge your SYNDR:

1. Locate the USB-C port on the device (protected by silicone cover)
2. Remove the silicone port cover
3. Connect the included USB-C cable to the device
4. Connect the other end to a USB power source
5. The LED indicator will illuminate during charging
6. Allow 60-90 minutes for a complete initial charge
7. Disconnect when fully charged
8. Replace the silicone port cover

Important: Use a standard 5V USB power source. The SYNDR is compatible with most USB wall adapters, computers, and power banks.

Understanding the Device

Components:

• Mouthpiece: Ceramic and silicone heat sink design, houses LED indicator
• Chamber: Bottom-loaded stainless steel herb chamber
• Body: Contains battery and heating element
• Power Button: Located on the body, controls all functions
• USB-C Port: Protected by silicone cover, used for charging

Powering On/Off

• Turn On: Click the power button 5 times rapidly within 2 seconds
• Turn Off: Click the power button 5 times rapidly within 2 seconds

The LED indicator will flash to confirm power state changes.

Usage Instructions

Preparing the Chamber

1. Remove the mouthpiece by gently pulling it from the body
2. Grind your herb to a medium-fine consistency (similar to dried oregano)
3. Load the chamber:
   • Use the cleaning brush or a small tool to funnel herb into the chamber
   • Fill to approximately 80% capacity
   • Do not pack too tightly; herb needs airflow for proper heating
4. Replace the mouthpiece securely

Loading Tips:

• Finely ground herb extracts more evenly
• Avoid overpacking, which restricts airflow
• A light tamp is acceptable; aggressive packing is not
• Fresh, properly cured herb produces the best vapor

Basic Operation

1. Power on the device (5 rapid clicks)
2. Wait for heat-up (approximately 30 seconds)
3. Feel for haptic feedback indicating ready temperature
4. Inhale slowly through the mouthpiece
5. Draw for 5-10 seconds with gentle, steady inhalation
6. Exhale and enjoy
7. Repeat until session ends (180 seconds) or herb is spent

Tips for Best Results:

• Slow, steady draws work better than quick, hard pulls
• Allow a few seconds between draws for the chamber to reheat
• Stir herb mid-session for more even extraction
• Higher temperatures extract more; lower temperatures taste better

Temperature Settings

Cycle through temperatures by single-clicking the power button during a session:

Setting	Temperature	LED Indication	Best For
1	360°F	Color 1	Maximum flavor, light vapor
2	380°F	Color 2	Balanced flavor and vapor
3	410°F	Color 3	Increased vapor production
4	440°F	Color 4	Maximum extraction, dense clouds

Temperature Selection Guide:

360°F (Low):

• Best for flavor enthusiasts
• Preserves terpenes and delicate compounds
• Light, wispy vapor
• Ideal for fresh, high-quality herb
• Herb remains greenish after session

380°F (Medium-Low):

• Good balance of flavor and visible vapor
• Suitable for everyday use
• Slightly more pronounced effects than lowest setting
• Herb turns light brown

410°F (Medium-High):

• Prioritizes vapor production over pure flavor
• Satisfying clouds with decent flavor
• More complete extraction
• Herb turns medium brown

440°F (High):

• Maximum extraction and vapor density
• Some flavor degradation at this temperature
• Best for users prioritizing effects over taste
• Herb turns dark brown
• Useful for finishing sessions started at lower temps

Session Timer

Each session runs for exactly 180 seconds (3 minutes). The device will:

• Vibrate to indicate session is ending
• Auto-shutoff after 180 seconds
• Display LED indication of session complete

Extending Your Session:

• The SYNDR cannot extend beyond 3 minutes per session
• To continue, simply power on again immediately after shutoff
• Back-to-back sessions are acceptable

Haptic Feedback

The SYNDR vibrates at key moments:

Vibration Pattern	Meaning
Single vibration at startup	Device heating
Double vibration	Ready to vape (target temperature reached)
Single vibration near end	Session ending soon

Charging

Battery Specifications

• Capacity: 880mAh internal lithium-ion
• Charging: USB-C, 5V
• Charge Time: 60-90 minutes
• Sessions Per Charge: 3-6 sessions (varies by temperature and usage)

Charging Procedure

1. Power off the device before charging (recommended)
2. Remove the silicone cover from the USB-C port
3. Connect USB-C cable to the device
4. Connect to a USB power source
5. LED indicates charging status
6. Disconnect when fully charged
7. Replace silicone port cover

Battery Tips

• Charge before battery is completely depleted
• Store with partial charge (40-60%) for extended storage
• Avoid charging unattended overnight
• Use standard 5V power sources
• The device can be used while charging (pass-through), though not recommended for optimal battery health

Battery Level Indicators

LED Behavior	Battery Status
Steady during use	Adequate charge
Flashing during use	Low battery
No response	Depleted, charge immediately

Care & Maintenance

After Each Session

1. Empty the chamber while herb is still slightly warm (easier removal)
2. Use the cleaning brush to sweep out loose material
3. Tap gently to dislodge stubborn particles
4. Wipe the mouthpiece interior with a dry swab

Weekly Cleaning

Chamber Cleaning:

1. Ensure the device is completely cool
2. Remove the mouthpiece
3. Use a cotton swab dampened with isopropyl alcohol (90%+)
4. Swab the chamber interior, removing any residue
5. Use the cleaning brush to address stubborn buildup
6. Allow to dry completely before use

Mouthpiece Cleaning:

1. Remove the mouthpiece from the body
2. Disassemble if possible (some models allow this)
3. Soak in isopropyl alcohol for 10-15 minutes
4. Use cleaning swabs to remove residue
5. Rinse with warm water
6. Dry completely before reassembling

Screen Cleaning/Replacement:

1. Remove the chamber screen carefully
2. Soak in isopropyl alcohol for 15-30 minutes
3. Use the brush to remove buildup
4. Rinse and dry completely
5. Replace in the chamber
6. If screen is damaged or clogged, replace with a new one (included spare)

Airpath Cleaning

1. With mouthpiece removed, blow gently through the chamber to clear the airpath
2. Use a pipe cleaner dampened with alcohol if needed
3. Ensure no alcohol enters the battery/electronics area
4. Allow to dry completely

Storage

• Store in a cool, dry location
• Empty the chamber before storage
• Keep away from direct sunlight and heat
• Replace silicone port cover to prevent debris entry
• Store upright to prevent residue from entering the airpath

Safety Information

General Safety

• Adult use only (21+)
• Keep away from children and pets
• Do not use if the device appears damaged
• Stop use immediately if overheating, unusual smell, or erratic behavior occurs
• Do not disassemble the device
• Use only for intended purpose (dry herb vaporization)

Battery Safety

• Use only the included or compatible USB-C cables
• Do not leave charging unattended for extended periods
• Do not expose to extreme temperatures
• Do not puncture, crush, or incinerate
• Dispose according to local electronics recycling regulations
• If battery swells or leaks, stop use immediately

Usage Safety

• Do not use while driving or operating machinery
• Allow cooling between extended sessions
• Do not overheat the device with rapid back-to-back sessions
• Do not use near flammable materials
• The chamber and mouthpiece become hot during use; handle with care

Material Safety

• Use only dry herb, not concentrates or liquids
• Do not use herbs that may be harmful when heated
• Ensure herb is properly dried and cured
• Do not use material with added chemicals or adulterants

Specifications

Specification	Value
Battery	880mAh Internal Li-ion
Temperature Settings	360°F / 380°F / 410°F / 440°F
Charging	USB-C (5V)
Charge Time	60-90 minutes
Heat-Up Time	~30 seconds
Session Duration	180 seconds
Height	4.25 inches
Dimensions	25mm x 18.2mm x 108.9mm
Heating Method	Conduction
Chamber Material	Stainless Steel
Mouthpiece	Ceramic/Silicone Heat Sink
Feedback	LED + Haptic
Auto-Shutoff	Yes

Troubleshooting

Device Won't Power On

1. Charge for at least 30 minutes
2. Click exactly 5 times within 2 seconds
3. Try a different USB-C cable
4. Try a different power source
5. Ensure the button isn't stuck or damaged
6. Contact Pulsar support if issue persists

No Vapor Production

1. Ensure herb is loaded in the chamber
2. Grind herb more finely
3. Check that herb isn't too dry (add humidity pack to storage container)
4. Increase temperature setting
5. Wait for full heat-up (haptic feedback)
6. Ensure airpath isn't blocked
7. Check that mouthpiece is properly seated
8. Clean chamber and screen

Weak Vapor

1. Increase temperature setting
2. Pack chamber slightly tighter (but not too tight)
3. Use slower, longer draws
4. Ensure herb is fresh and properly cured
5. Clean the device if residue is present
6. Try stirring herb mid-session

Harsh or Bad-Tasting Vapor

1. Lower temperature setting
2. Clean the chamber and airpath thoroughly
3. Ensure screen isn't clogged with residue
4. Use fresher herb
5. Try smaller loads for better airflow
6. Allow device to cool between sessions

Uneven Extraction

1. Grind herb more consistently
2. Don't pack too tightly
3. Stir herb mid-session with a tool
4. Use medium temperature for initial heating
5. Finish at higher temperature for complete extraction

Device Overheating

1. Stop use immediately
2. Allow to cool completely before resuming
3. Avoid rapid back-to-back sessions
4. Check that chamber isn't overpacked
5. If persistent, contact Pulsar support

Charging Issues

1. Remove silicone port cover
2. Check USB-C cable connection
3. Try different cable
4. Try different power source
5. Clean charging port with dry brush
6. Contact support if port appears damaged

Warranty Information

The Pulsar SYNDR includes a manufacturer warranty covering defects in materials and workmanship. The warranty does not cover:

• Damage from misuse or accidents
• Normal wear and tear
• Water or liquid damage
• Unauthorized modifications
• Use with incompatible materials (concentrates, etc.)
• Cosmetic damage

Keep your proof of purchase for warranty claims. Contact Pulsar directly or your authorized retailer for warranty service.

Related: Pulsar SYNDR Review