Dr. Dabber Switch² Manual: Complete Setup, Usage & Troubleshooting Guide

Overview

The Dr. Dabber Switch² is a premium e-rig featuring induction heating technology. Unlike traditional coil-based devices, the Switch² uses electromagnetic fields to heat inserts directly, providing cleaner flavor and more even vaporization.

This manual covers setup, operation, heating modes, app connectivity, and maintenance for optimal performance.

What's in the Box

• Dr. Dabber Switch² base unit
• Glass percolator attachment
• 20mm quartz insert
• Carb cap with magnetic attachment
• Dr. Dabber Drop heated loading tool
• USB-C charging cable
• 36W charging adapter
• User manual

Note: Contents may vary by retailer or bundle purchased.

Device Overview

Components

• Base Unit: Houses the induction heating system, battery, controls, and LED lighting
• Glass Attachment: Borosilicate percolator for water filtration
• Insert: Quartz, sapphire, titanium, or ALN heating surface
• Carb Cap: Controls airflow and retains heat during sessions

Button Functions

Action	Function
5 clicks	Power on/off
3 clicks	Cycle heating modes
2 clicks	Start heating session
Hold	Manual heating (while pressed)

Getting Started

Initial Charge

Before first use, fully charge your Switch²:

1. Connect the USB-C cable to the base unit
2. Use the included 36W adapter for fastest charging
3. LED indicators show charging status
4. Full charge takes 60-90 minutes
5. The device is ready when LEDs indicate full

Note: You can use the Switch² while charging (pass-through charging).

Assembling the Device

1. Attach the glass:

   • Ensure the silicone seal on the base is properly positioned
   • Align the glass attachment and press down firmly
   • The glass should sit securely without wobbling

2. Add water:

   • Remove the glass attachment
   • Fill with room temperature water
   • Water level should be just above the percolator holes
   • Do not overfill—this causes splashback

3. Install the insert:

   • Place the insert into the heating chamber
   • Ensure it sits flat and centered
   • The insert must be properly seated for induction heating to work

4. Attach the carb cap:

   • The carb cap magnetically attaches to the glass
   • Keep it nearby during sessions for easy access

Powering On/Off

• Turn On: Click the power button 5 times rapidly within 2 seconds
• Turn Off: Click the power button 5 times rapidly within 2 seconds

LED lighting will indicate power status and current settings.

Understanding Induction Heating

The Switch² uses induction heating rather than traditional coils:

How It Works

1. Electromagnetic coils in the base create a magnetic field
2. The field induces electrical currents in the insert's metal components
3. These currents generate heat directly in the insert
4. An infrared sensor monitors actual insert temperature

Benefits

• Even heating: The insert heats uniformly for consistent vaporization
• No coil contact: Concentrates never touch heating elements
• Better flavor: Cleaner vapor path preserves terpene profiles
• Temperature accuracy: Infrared sensing provides precise control

Insert Compatibility

Only official Dr. Dabber inserts work with the Switch² induction system:

Insert	Material	Best For
Quartz (included)	Pure quartz	Balanced flavor and heating
Sapphire Plus	Lab-grown sapphire	Maximum flavor, easy cleaning
Titanium	Medical-grade titanium	Fast heating, dry herbs
ALN	Aluminum nitride	Premium heat retention

Third-party inserts may not heat properly.

Heating Modes

The Switch² offers three dynamic heating profiles:

Descent Mode

Replicates traditional torch dabbing:

• Starts at your set temperature
• Gradually decreases (1°F per second)
• Mimics natural banger cooling
• Best for: Traditional dabbing experience

Ascent Mode

Perfect for cold starts:

• Begins at a lower temperature
• Gradually increases to your set temperature
• Preserves terpenes through slow heating
• Best for: Flavor enthusiasts, live resin

Steady Mode

Maintains consistent temperature:

• Holds your set temperature throughout the session
• Predictable, repeatable results
• Best for: Consistent dosing, sharing

Changing Modes

Without app: Click the power button 3 times to cycle through modes. LED color indicates current mode.

With app: Select heating mode directly from the app interface.

Temperature Settings

Temperature Range

The Switch² operates from 250-650°F:

Range	Temperature	Best For
Low	250-400°F	Maximum flavor, live resin, terpene preservation
Medium	400-500°F	Balanced vapor and flavor
High	500-650°F	Maximum vapor, thick concentrates

Setting Temperature

Without app: Use button controls for preset temperature levels.

With app: Set precise temperature in single-degree increments from 250-650°F.

Temperature Recommendations

• Live resin, rosin: 350-450°F (Ascent mode)
• Shatter, wax: 450-550°F (Steady mode)
• Thick concentrates: 500-600°F (Descent mode)
• Flavor testing: 300-400°F (Ascent mode)

Using the Dr. Dabber App

Installation

1. Download "Dr. Dabber" from the App Store or Google Play
2. Create an account or sign in
3. Enable Bluetooth on your phone
4. Power on the Switch²
5. The app will detect and connect to your device

App Features

Temperature Control:

• Set precise temperature (250-650°F)
• Create custom temperature profiles
• Save favorite settings

Session Settings:

• Adjust hold times
• Set session duration
• Customize heating curves

LED Customization:

• Choose preset lighting themes
• Create custom colors
• Sync lighting to temperature

Usage Tracking:

• Monitor session counts
• View average temperatures
• Track battery health

Operating Without the App

The Switch² functions fully without the app:

• Power on/off: 5 clicks
• Cycle heating modes: 3 clicks
• Start session: 2 clicks or hold button
• Temperature adjusts via mode selection

Usage Instructions

Loading Concentrate

1. Power on the device (5 clicks)
2. Remove the carb cap
3. Use the Drop tool or dab tool to load concentrate
4. Place concentrate directly on the insert surface
5. Start with a rice-grain sized amount
6. Replace the carb cap

Tips:

• The Drop heated tool helps with sticky concentrates
• Do not overload—excess concentrate can overflow
• Room temperature concentrates are easier to handle

Taking a Dab

1. Ensure concentrate is loaded and carb cap is in place
2. Select your temperature and heating mode
3. Double-click to start a session, or hold the button for manual heating
4. Wait for the device to reach temperature (5-30 seconds)
5. Inhale slowly through the mouthpiece
6. Rotate the carb cap to control airflow
7. Continue inhaling until vapor diminishes

Session Tips

• Start with lower temperatures and increase as needed
• Longer, slower draws produce smoother vapor
• The carb cap is essential for proper airflow
• Clean the insert while warm for easy maintenance

Water Filtration

Proper Water Level

1. Remove the glass attachment
2. Fill with clean, room temperature water
3. Level should be 1-2cm above the percolator holes
4. Do not overfill—this causes splashback

Water Guidelines

Level	Result
Too low	Insufficient filtration, harsh hits
Correct	Smooth, cooled vapor
Too high	Water splashes into mouth

Water Tips

• Change water daily for best flavor
• Room temperature water works best
• Empty water when not in use
• Never use hot water (risk of thermal shock)

Using the Drop Tool

The included Drop heated loading tool makes concentrate handling easier:

Drop Operation

1. Turn on the Drop (5 clicks)
2. Select heat level (low or high)
3. Dip the tip into your concentrate
4. The heated tip melts and holds the concentrate
5. Touch the tip to the insert to deposit
6. Turn off the Drop when finished

When to Use Drop

• Sticky concentrates that cling to cold tools
• Precise loading of small amounts
• Transfer from containers to insert
• Any time you want cleaner loading

Battery Information

Specifications

• Capacity: Provides ~30 heating cycles
• Charging: USB-C pass-through
• Charge Time: 60-90 minutes
• Adapter: 36W included (faster than standard)

LED Battery Indicators

Display	Battery Level
Full illumination	75-100%
Partial illumination	25-75%
Low light	Below 25%
Flashing	Critical - charge immediately

Charging Tips

• Use the included 36W adapter for fastest charging
• Pass-through charging allows use while plugged in
• Any USB-C source works, but may charge slower
• Store with partial charge for long-term storage

Maintenance

After Each Session

1. While insert is still warm, use a Q-tip to clean residue
2. Dry Q-tip first, then isopropyl-dampened if needed
3. Wipe the carb cap clean
4. Empty water if not using again soon

Weekly Cleaning

Insert:

1. Remove insert from the device
2. Soak in isopropyl alcohol (90%+) for 15-30 minutes
3. Use Q-tips to clean any remaining residue
4. Rinse with warm water
5. Dry completely before use

Glass Attachment:

1. Remove from base
2. Empty water completely
3. Fill with isopropyl alcohol
4. Let soak for 30 minutes to 1 hour
5. Shake gently to remove residue
6. Rinse thoroughly with warm water
7. Air dry completely

Base Unit:

1. Wipe exterior with slightly damp cloth
2. Clean around the heating chamber with dry Q-tips
3. Never submerge the base in liquid
4. Keep USB-C port free of debris

Deep Cleaning

For stubborn residue:

1. Soak insert overnight in isopropyl alcohol
2. Use pipe cleaners for glass attachment
3. For the heating chamber, use dry Q-tips only
4. Allow all components to dry 24 hours before reassembly

Insert Replacement

Replace your insert when you notice:

• Persistent off-flavors despite cleaning
• Visible cracks or chips
• Uneven heating or hot spots
• Discoloration that won't clean

Safety Information

General Safety

• Adult use only (21+)
• Keep away from children and pets
• Do not use if device appears damaged
• Stop use if device overheats unexpectedly
• Do not disassemble the base unit

Electrical Safety

• Use only included or compatible chargers
• Do not charge on flammable surfaces
• Unplug when fully charged for overnight storage
• Keep away from water (base unit)
• Inspect cables for damage before use

Glass Safety

• Handle glass attachment carefully
• Do not use if cracked or chipped
• Avoid thermal shock (no hot water)
• Store safely when not in use
• Replacement glass is available if needed

Insert Safety

• Inserts become extremely hot during use
• Allow cooling before handling
• Use included tools for loading, not fingers
• Replace damaged inserts immediately

Specifications

Specification	Value
Temperature Range	250-650°F
Heat-Up Time	5-30 seconds
Battery Life	~30 heating cycles
Charge Time	60-90 minutes
Charging	USB-C pass-through
Dimensions	9" × 4"
Weight	25.6 oz (726g)
Insert Size	20mm
Heating	Induction with IR sensor
Connectivity	Bluetooth (app)
Warranty	2 years

Troubleshooting

Device Won't Power On

1. Ensure battery is charged
2. Use included 36W adapter for faster charging
3. Click exactly 5 times within 2 seconds
4. Check USB-C port for debris
5. Try a different charging cable

Insert Not Heating

1. Verify insert is properly seated and centered
2. Remove and reinstall the insert
3. Check that you're using an official Dr. Dabber insert
4. Ensure the heating chamber is clean
5. Contact support if issue persists

Weak Vapor Production

1. Increase temperature setting
2. Ensure carb cap is creating proper seal
3. Check that concentrate is on the insert (not sides)
4. Clean the insert if residue is visible
5. Try a different heating mode

App Connection Issues

1. Verify Bluetooth is enabled
2. Device must be powered on
3. Close and reopen the app
4. Restart your phone
5. Unpair and re-pair the device

Glass Attachment Issues

1. Check silicone seal position
2. Ensure glass is pressed firmly onto base
3. Inspect seal for damage
4. Clean both surfaces
5. Replace seal if worn

Battery Draining Quickly

1. Lower temperature settings
2. Shorter sessions use less power
3. Avoid leaving device powered on when not in use
4. USB-C pass-through provides unlimited sessions
5. Battery capacity may decrease over time

Warranty Information

The Dr. Dabber Switch² includes a 2-year warranty covering:

• Battery defects
• Electrical component failures
• Charging system issues
• Manufacturing defects

Warranty does not cover:

• Physical damage from drops or misuse
• Normal wear and tear
• Glass breakage
• Consumable parts (inserts)
• Water damage to base unit
• Unauthorized modifications

For warranty service, contact Dr. Dabber support with proof of purchase.

Related: Dr. Dabber Switch² Review | Dr. Dabber Boost Evo Manual