Lookah Dinosaur Manual: Setup, Usage & Troubleshooting: Complete Setup & Usage Guide

Overview

The Lookah Dinosaur is a uniquely designed electric dab rig featuring a playful dinosaur shape with serious performance capabilities. This manual provides complete instructions for assembling, operating, maintaining, and troubleshooting your Dinosaur e-rig.

The device features a 950mAh battery, three voltage settings, magnetic assembly, and a built-in dab tool. Understanding proper operation ensures optimal performance and maximizes your enjoyment of this distinctive device.

What's in the Box

Your Lookah Dinosaur kit includes:

• 1x Lookah Dinosaur Electronic Dab Rig Base
• 1x Magnetic Ring with Dinosaur Glass Percolator
• 1x Mouthpiece Tip Stopper
• 2x 710 Type D Quartz Coils (dual core design)
• 1x Dab Tool (built into device)
• 1x USB-C Charging Cable
• 1x User Manual

Getting Started

Initial Charge

Before first use, fully charge your Dinosaur:

1. Locate the USB-C charging port on the device base
2. Connect the included USB-C cable
3. Connect to a 5V USB power adapter
4. The LED will illuminate during charging
5. Charge for approximately 70 minutes until fully charged
6. Disconnect when charging is complete

Note: The Dinosaur features fast USB-C charging that achieves full charge in about 70 minutes.

Assembly

1. Install coil: Ensure a 710 Type D quartz coil is threaded into the base (one comes pre-installed)
2. Attach bubbler: Position the glass percolator over the base - the magnetic connection will pull it into place
3. Add water: Fill the bubbler with water just above the percolator holes
4. Install stopper: Insert the mouthpiece tip stopper

Powering On/Off

• Turn On: Click the power button (dinosaur nose) 5 times rapidly within 2 seconds
• Turn Off: Click the power button 5 times rapidly within 2 seconds
• Auto-Off: Device powers off after 5 minutes of inactivity

The LED display illuminates when powered on, showing battery level and voltage setting.

Usage Instructions

Basic Operation

1. Power on with 5 rapid clicks of the nose button
2. Select voltage by double-clicking to cycle through settings
3. Load concentrate using the built-in dab tool - apply a rice-grain sized amount to the coil
4. Press and hold the power button to begin heating
5. Wait for preheat - the 8-second auto preheat warms concentrate
6. Inhale slowly through the mouthpiece as vapor forms
7. Release the button when finished with your draw
8. Power off with 5 rapid clicks when session is complete

Voltage Settings

Double-click the power button to cycle through voltage options:

Setting	Voltage	LED Color	Best For
Low	3.5V	Green	Maximum flavor, smooth hits
Medium	3.7V	Blue	Balanced flavor and vapor
High	3.9V	White	Maximum vapor production

Recommendations:

• Start on low voltage for flavor exploration
• Medium setting suits most concentrates
• High setting for thick concentrates or maximum clouds
• The device remembers your last setting

8-Second Auto Preheat

The Dinosaur includes automatic preheating:

1. When you press and hold the power button, preheat begins automatically
2. The device warms the coil at reduced power for approximately 8 seconds
3. This melts concentrate evenly before full vaporization
4. After preheat, full heating engages
5. Haptic feedback (vibration) signals when ready

The preheat function creates smoother, more consistent hits by conditioning concentrate before intense heat is applied.

Using the Built-in Dab Tool

The Dinosaur features an integrated dab tool:

1. Locate the dab tool component on your device (position varies by color variant)
2. Remove the tool from its storage position
3. Use the tool tip to collect a rice-grain sized amount of concentrate
4. Apply concentrate to the quartz coil surface
5. Return the tool to its storage position
6. The integrated tool eliminates the need for separate accessories

LED Display

The LED screen communicates device status:

Display	Meaning
Green	Low voltage (3.5V) active
Blue	Medium voltage (3.7V) active
White	High voltage (3.9V) active
Battery icon	Current charge level
Flashing	Low battery or error condition

Water Level

Proper water level ensures optimal filtration:

1. Remove the mouthpiece stopper
2. Add water through the top opening
3. Fill until water just covers the percolator holes
4. Do not overfill - excessive water causes splashing
5. Test with a dry draw before heating
6. Adjust if water reaches the mouthpiece

Charging

Charging Procedure

1. Connect the included USB-C cable to the charging port
2. Connect to a 5V USB power adapter
3. The LED indicates charging status
4. Full charge takes approximately 70 minutes
5. Disconnect when fully charged

Battery Performance

• Capacity: 950mAh
• Heat cycles per charge: Up to 100
• Fast charging via USB-C
• Charge time: ~70 minutes (0 to full)

Charging Safety

• Use only 5V adapters to prevent battery damage
• Charge in a cool, dry environment
• Do not leave charging unattended for extended periods
• Use quality USB-C cables
• Do not charge if the device appears damaged

Care & Maintenance

Daily Cleaning

After each session:

1. Allow the device to cool completely
2. Use a cotton swab to wipe residue from the warm coil
3. Empty the bubbler water
4. Wipe the mouthpiece with a clean cloth

Weekly Deep Cleaning

Glass Percolator:

1. Remove from the base by lifting away from the magnetic connection
2. Empty all water
3. Fill with isopropyl alcohol (90%+ recommended)
4. Let soak for 20-30 minutes
5. Shake gently to dislodge residue
6. Rinse thoroughly with warm water
7. Air dry completely before reassembly

Coils:

1. Remove by unscrewing counter-clockwise
2. Soak in isopropyl alcohol for 30 minutes
3. Use a cotton swab for stubborn residue
4. Rinse with warm water
5. Dry completely before reinstalling

Base Unit:

1. Wipe exterior with a slightly damp cloth
2. Clean threading with a dry cotton swab
3. Never submerge the base - it contains electronics
4. Keep the USB-C port dry and clear

Storage

For optimal storage:

• Empty and dry the glass percolator
• Remove the coil if storing long-term
• Store in a cool, dry place
• Keep away from direct sunlight
• Handle the glass bubbler carefully during storage

Coil Replacement

Replace the coil when:

• Flavor degrades or tastes off
• Vapor production decreases significantly
• Buildup cannot be cleaned
• Physical damage is visible

To replace:

1. Remove the old coil (counter-clockwise)
2. Thread the new Type D coil (clockwise)
3. Hand-tighten - do not overtighten
4. Run a brief heating cycle before loading concentrate

Safety Information

General Safety

• Age Restriction: For adult use only (21+)
• Keep Away from Children: Store securely out of reach
• Intended Use: Use only with legal concentrates
• Supervision: Never leave unattended while operating

Built-in Protections

The Dinosaur includes multiple safety features:

• Open Circuit Protection: Detects when coil is missing
• Short Circuit Protection: Prevents electrical shorts
• Overcharge Protection: Safeguards battery during charging
• Voltage Surge Protection: Handles power fluctuations

Usage Precautions

• Handle the glass bubbler carefully to prevent breakage
• Don't touch the coil during or immediately after use
• Allow cooling between consecutive sessions
• Keep water in the bubbler for cooled vapor
• Use on stable surfaces to prevent tipping
• Don't operate while driving or operating machinery

Battery Safety

• Use only 5V USB-C adapters
• Don't expose to extreme temperatures
• Don't puncture, crush, or disassemble
• Dispose of properly per local regulations

Warranty Information

The Lookah Dinosaur is covered by a limited manufacturer's warranty:

• Duration: 3 months from date of purchase
• Coverage: Defects in materials and workmanship under normal use
• Exclusions: Physical damage, water damage (to electronics), misuse, unauthorized modifications, coils (consumable), glass breakage

Contact Lookah customer support with proof of purchase for warranty service.

Related: Lookah Dinosaur Review