Overview
The Cartisan Inspector is a Sherlock-style 510 battery that combines vintage pipe aesthetics with modern vaping technology. Featuring an LCD display, wide voltage range (1.8V-4.2V), and both auto-draw and button activation, the Inspector offers more functionality than typical cartridge batteries while maintaining a distinctive appearance.
This manual covers everything you need to know about setting up, operating, and maintaining your Inspector, including LCD display functions, voltage optimization, and troubleshooting common issues.
What's in the Box
- Cartisan Inspector 510 Battery
- USB-C Charging Cable
- User Guide
Note: Cartridges are sold separately. The Inspector is compatible with any standard 510-threaded cartridge.
Getting Started
Initial Charge
Before first use, fully charge your Inspector:
- Locate the USB-C charging port on the device body
- Connect the included USB-C cable to the Inspector
- Connect the other end to a USB power source (5V/1A-2A recommended)
- The LCD display will show charging progress
- Charge until the LCD indicates 100% (approximately 1-2 hours)
- Disconnect the cable when fully charged
Important: Always complete the initial charge before first use for optimal battery performance.
Understanding the Inspector Design
The Inspector features several key components:
- Stem/Mouthpiece - The curved pipe stem you draw from
- Hidden Cartridge Chamber - Located inside the stem where your 510 cart threads in
- Body - The main curved section containing the battery and LCD
- Power Button - Side-mounted button for power and controls
- LCD Display - Shows voltage, battery percentage, and puff count
- LED Bowl - Illuminates during use for aesthetic effect
- USB-C Port - For charging the internal battery
Attaching a Cartridge
The Inspector's hidden design conceals your cartridge within the stem:
- Ensure the device is powered off (recommended during cartridge changes)
- Locate the 510 threading inside the stem opening
- Hold your cartridge by the body, not the mouthpiece
- Align the cartridge's 510 threads with the internal threading
- Gently screw clockwise until snug—do not overtighten
- The cartridge should sit mostly concealed within the stem
Most standard 510 cartridges up to 2G capacity (approximately 14mm diameter) fit properly.
Powering On/Off
- Turn On: Click the power button 5 times rapidly within 2 seconds
- Turn Off: Click the power button 5 times rapidly within 2 seconds
- The LCD display activates when powered on and goes dark when off
- The device may provide haptic feedback (vibration) to confirm power state
Always power off your Inspector when not in use to conserve battery and prevent accidental activation.
Understanding the LCD Display
The Inspector's LCD display provides real-time information unavailable on basic LED batteries.
Display Information
| Display Element | What It Shows |
|---|---|
| Voltage Reading | Current voltage setting (1.8V-4.2V) |
| Battery Percentage | Remaining charge (0-100%) |
| Puff Counter | Cumulative number of draws taken |
Reading the Display
- Voltage updates when you cycle through settings (3 clicks)
- Battery percentage decreases gradually during use
- Puff counter increments with each draw, tracking total usage
The display illuminates when the device is on and during active use, then dims or turns off to conserve power when idle.
Voltage Settings
The Inspector offers four voltage levels spanning 1.8V to 4.2V—the widest range available on most cartridge batteries.
Changing Voltage
Click the power button 3 times rapidly to cycle through voltage settings. Watch the LCD display to confirm your selection.
Voltage Guide
| Voltage Range | Best For | Experience |
|---|---|---|
| 1.8V - 2.2V | Thin oils, live resin, CBD | Cool vapor, maximum flavor |
| 2.4V - 2.8V | Standard cartridges | Balanced flavor and vapor |
| 3.0V - 3.4V | Medium-thick oils | Increased vapor production |
| 3.6V - 4.2V | Thick distillates | Maximum clouds, less flavor |
Voltage Selection Tips
- Start low: Begin at 2.4V and increase only if vapor production is insufficient
- Match your oil: Thinner oils work best at lower voltages; thick distillates need higher settings
- Prioritize flavor: Lower voltages preserve delicate terpenes and produce smoother hits
- Live resin: Use 1.8V-2.4V to protect temperature-sensitive terpene profiles
- Avoid burning: If hits taste harsh or burnt, decrease voltage immediately
Using Auto-Draw vs Button Activation
The Inspector supports two activation methods simultaneously—no switching required.
Button Activation
- Ensure the device is powered on
- Press and hold the power button
- Inhale from the mouthpiece while holding the button
- Release the button to end the draw
Benefits: Precise control over each hit, no accidental activation
Auto-Draw Activation
- Ensure the device is powered on
- Simply inhale from the mouthpiece
- The device activates automatically when airflow is detected
- Stop inhaling to end the draw
Benefits: Hands-free convenience, natural drawing experience
Which to Use?
- Use button activation when you want precise control or when the cartridge has restricted airflow
- Use auto-draw for convenience and a more natural pipe-smoking feel
- Both methods can be alternated freely during the same session
Preheat Function
The preheat function warms thick oils to improve flow and vapor production.
Activating Preheat
- Ensure the device is powered on
- Double-click the power button quickly (within 1 second)
- The device vibrates to confirm preheat activation
- Preheat runs for approximately 1.5 seconds
- Inhale immediately after preheat completes for best results
When to Use Preheat
- With thick distillate cartridges
- In cold weather when oil becomes viscous
- When a cartridge hasn't been used in several days
- If you notice reduced vapor production from a new cart
Note: Don't overuse preheat on thin oils—it's designed for thick concentrates that need warming.
Charging
How to Charge
- Power off the device (recommended but not required due to passthrough)
- Connect the USB-C cable to the Inspector's charging port
- Connect the other end to a USB power source
- Monitor charging progress on the LCD display
- Charge until the display shows 100%
- Disconnect the cable when fully charged
Passthrough Charging
The Inspector supports passthrough use—you can vape while the device charges. Simply connect the USB-C cable and continue using the device normally. The LCD display will show both charging status and usage information.
Charging Times
- Full charge from empty: 1-2 hours
- Quick top-up (50% to 100%): 30-45 minutes
Battery Life Expectations
With the 650mAh capacity, expect:
- Light use (10-15 puffs/day): 3-4 days between charges
- Moderate use (25-35 puffs/day): 2 days between charges
- Heavy use (50+ puffs/day): Daily charging recommended
Higher voltage settings consume more power. Using 1.8V-2.4V extends battery life compared to 3.6V-4.2V.
Charging Best Practices
- Use the included USB-C cable or a quality replacement
- Use standard 5V USB power sources (wall adapters, computers)
- Avoid fast chargers rated above 5V/2A
- Don't leave the device charging unattended for extended periods
- Charge before the battery is completely depleted
- Avoid charging in extreme temperatures
The LED Bowl Light
The Inspector features an LED light in the bowl area that illuminates during use, creating a glowing effect reminiscent of lit tobacco.
How It Works
- The LED activates automatically when you draw (auto-draw) or press the button
- It illuminates throughout the duration of your hit
- The LED turns off when you stop drawing
This feature is purely aesthetic and doesn't indicate device status. For status information, always refer to the LCD display.
Care & Maintenance
Regular Cleaning
Maintain your Inspector's performance with routine cleaning:
Weekly Maintenance:
- Remove the cartridge
- Use a dry cotton swab to clean the 510 threading inside the stem
- Wipe any oil residue from the stem interior
- Clean around the power button to prevent sticking
- Wipe the body and mouthpiece with a soft, dry cloth
Monthly Deep Clean:
- Perform all weekly cleaning steps
- Use isopropyl alcohol (90%+) on a cotton swab for stubborn residue
- Clean the stem opening and threading thoroughly
- Allow all cleaned areas to dry completely before use
- Inspect the USB-C port for debris
Cleaning the Hidden Cartridge Area
The stem threading can accumulate oil residue:
- Remove the cartridge completely
- Look inside the stem to inspect threading
- Insert a dry cotton swab and twist to clean grooves
- For stuck residue, dampen the swab lightly with isopropyl alcohol
- Allow to dry for 5-10 minutes before attaching a new cartridge
Storage Guidelines
- Store in a cool, dry place away from direct sunlight
- Keep away from heat sources and extreme temperatures
- Store upright with the stem facing up when a cartridge is attached
- For long-term storage (1+ month), remove the cartridge and charge to 50%
- Protect from physical impacts—the plastic body can crack if dropped
Safety Information
Important Warnings
- Keep away from children and pets
- This device is intended for adult use only (21+)
- Do not use if the device appears damaged or cracked
- Stop use immediately if the device becomes excessively hot
- Do not modify or attempt to disassemble the battery
- Use only with compatible 510-threaded cartridges
Battery Safety
- Do not expose to fire, open flames, or extreme heat
- Do not puncture, crush, or physically damage the device
- Do not short-circuit the battery terminals
- Dispose of properly according to local lithium battery regulations
- If the device swells, leaks, or produces unusual odors, stop use immediately
Usage Precautions
- Do not use while driving or operating machinery
- Do not use near flammable materials
- Ensure adequate ventilation when vaping indoors
- Consult a physician if you have relevant health conditions
- The device gets warm during extended use—this is normal within reason
Specifications Summary
| Specification | Value |
|---|---|
| Battery Capacity | 650mAh Lithium-Ion |
| Voltage Range | 1.8V - 4.2V |
| Voltage Settings | 4 levels |
| Activation | Button + Auto-draw |
| Display | LCD (voltage, battery %, puff count) |
| Preheat | Yes (1.5 seconds, double-click) |
| Passthrough Charging | Yes |
| Charging | USB-C |
| Charge Time | 1-2 hours |
| Threading | 510 |
| Cartridge Capacity | Up to 2G |
| Dimensions | 5.3" x 3.4" x 1.58" |
| Weight | 227g |
| LED Bowl Light | Yes |
| Haptic Feedback | Yes |
| Auto-Shutoff | Yes |
| Overcharge Protection | Yes |
| Warranty | 30 days |
Warranty & Support
The Cartisan Inspector includes a 30-day limited warranty covering manufacturing defects.
Warranty Coverage
- Manufacturing defects in materials and workmanship
- Battery malfunction under normal use conditions
- LCD display failure
- Button or control malfunctions
Not Covered
- Physical damage from drops, impacts, or misuse
- Water or liquid damage
- Unauthorized modifications
- Normal wear and tear
- Cosmetic damage
- Cartridge compatibility issues
Getting Support
For assistance with your Inspector:
- Visit cartisan.tech for FAQs and resources
- Contact Cartisan customer support through their website
- Have your purchase receipt ready for warranty claims
Related: Cartisan Inspector Review